Guest Chico Posted October 5, 2009 Share Posted October 5, 2009 (edited) Ciao a tutti, ho appena installato il G25 al posto del mio moribondo DFP e la differenza è a dir poco abissale!!!! Sto provando a modificare il file plr di gtr2 mettendo queste stringhe (per comodità le ho messe alla fine) al posto delle originali. Secondo voi, visto che sono prese da quello che usavo col DFP, vanno bene? O esistono confiuragzioni esclusive e migliori per il G25? inoltre: nel pannello logitech che valori vanno messi per il G25 alle seguenti voci: [PANNELLO IMPOSTAZIONI SPECIFICHE DI GIOCO GTR2] Forza effetti globali: %? Forza effetto molla: %? Attiva molla di centratura (va flaggato??): %? Impostazioni speciale volante (va flaggato??) Regista pedali combinati (ovviamente no): Gradi rotazione (molto soggettivo): Utilizza impostazioni speciali di gioco: (va flaggato??) Consenti al gioco di adattare le impostazioni: (va flaggato??) --------------------------------------------------------------- Una volta lanciato GTR2, alla voce controlli, come vanno settati i seguenti valori: sensibilità acceleratore: sensibilità freno: sensibilità frizione: zona morta acceleratore zona morta freno: zona morta frizione: sterza secondo velocità: Queste sono le stringhe relative al ffb del file plr di gtr2 (datemi il vostro feedback) FFB Device Type="4" // Type of FFB controller: 0=none 1=wheel, 2=stick/custom, 3=rumble pad. FFB Effects Level="1" // Number of FFB effects to use: 0=No Effects, 1=Low, 2=Medium, 3=High, 4=Full, 5=Custom. FFB Gain="0.81000" // Strength of Force Feedback effects. Range 0.0 to 1.0. FFB Throttle FX on steer axis="1" // 0 = Throttle effects on throttle axis, 1 = throttle effects on steering axis. FFB Brake FX on steer axis="1" // 0 = Brake effects on brake axis, 1 = brake effects on steering axis. FFB steer vibe freq mult="0.07000" // Controls frequency of steering vibration. Recommended: 0.5 to 1.0, 0.0 disables steering vibration. FFB steer vibe zero magnitude="0.03500" // Magnitude of steering vibration at 0mph (reference point). FFB steer vibe slope="0.00000" // Slope of line defining magnitude as a function of frequency (used with FFB steer vibe zero magnitude). FFB steer vibe wave type="0" // Type of wave to use for vibe: 0=Sine, 1=Square, 2=Triangle, 3=Sawtooth up, 4=Sawtooth down. FFB steer force average weight="0.90000" // How much weight is given to new steering force calculations each frame (0.01 - 1.0). Lower values will smooth out the steering force, but will also add latency. FFB steer force exponent="0.90000" // Steering force output "sensitivity". Range 0.0 to infinity. 0.0 to 1.0 = higher sensitivity, greater than 1.0 = lower sensitivity. FFB steer force input max="-11500.00000" // Recommended: 11500 (-11500 if controller pulls in the wrong direction). FFB steer force output max="1.80000" // Maximum force output of steering force, recommendation 0.8 to 2.0 FFB steer force grip weight="1.00000" // Range 0.0 to 1.0, recommended: 0.4 to 0.9. How much weight is given to tire grip when calculating steering force. FFB steer force grip factor="0.75000" // Range 0.0 to 1.0, recommended: 0.2 to 0.6. How much of a factor the front wheel grip is on the steering weight. FFB steer update thresh="0.0002500000" // Amount of change required to update steer force/vibe (0.0 - 1.0). Lower values = steering force updated more frequently = lower frame rate. FFB steer friction coefficient="0.10000" // Coefficient to use for steering friction. Range: -1.0 to 1.0 FFB steer friction saturation="1.00000" // Saturation value to use for steering friction. Range: 0 - 1.0 FFB steer damper coefficient="0.10000" // Coefficient to use for steering damper. Range: -1.0 to 1.0 FFB steer damper saturation="1.00000" // Saturation value to use for steering damper. Range: 0 - 1.0 FFB throttle vibe freq mult="0.40000" // Scales actual engine frequency to force FFB vibration frequency. Suggested range: 0.10 to 0.50 FFB throttle vibe zero magnitude="0.09000" // Magnitude of engine vibration at 0rpm (reference point). FFB throttle vibe slope="0.00000" // Slope of line defining magnitude as a function of frequency (used with FFB throttle vibe zero magnitude). FFB throttle vibe wave type="0" // Type of wave to use for vibe: 0=Sine, 1=Square, 2=Triangle, 3=Sawtooth up, 4=Sawtooth down. FFB throttle vibe update thresh="0.02000" // Amount of change required to update throttle vibe (0.0 - 1.0) FFB brake vibe freq mult="0.90000" // Scales actual brake rotational frequency to force feedback vibration frequency. FFB brake vibe zero magnitude="0.09000" // Magnitude of brake vibration at 0mph (reference point). FFB brake vibe slope="0.00000" // Slope of line defining magnitude as a function of frequency (used with FFB brake vibe zero magnitude). FFB brake vibe wave type="0" // Type of wave to use for vibe: 0=Sine, 1=Square, 2=Triangle, 3=Sawtooth up, 4=Sawtooth down. FFB brake vibe update thresh="0.02000" // Amount of change required to update brake vibe (0.0 to 1.0) FFB rumble strip magnitude="0.60000" // How strong the rumble strip rumble is. Range 0.0 to 1.0, 0.0 disables effect. FFB rumble strip freq mult="0.50000" // Rumble stip frequency multiplier 1.0 = one rumble per wheel rev. FFB rumble strip wave type="0" // Type of wave to use for vibe: 0=Sine, 1=Square, 2=Triangle, 3=Sawtooth up, 4=Sawtooth down. FFB rumble strip pull factor="-1.00000" // How strongly wheel pulls right/left when running over a rumble strip. Suggested range: -1.5 to 1.5. FFB rumble strip update thresh="0.07500" // Amount of change required to update rumble strip effect (0.0 - 1.0) FFB jolt magnitude="1.70000" // How strong jolts from other cars (or walls) are. Suggested Range: -2.0 to 2.0. Ringrazio tutti anticipatamente!!!! Edited October 5, 2009 by Chico Link to comment Share on other sites More sharing options...
Guest Chico Posted October 6, 2009 Share Posted October 6, 2009 Dai ragazzi, almeno linkatemi qualcosa... Link to comment Share on other sites More sharing options...
Guest Chico Posted October 7, 2009 Share Posted October 7, 2009 Diponibile finanche a pagare:-))) Link to comment Share on other sites More sharing options...
Guest Chico Posted October 8, 2009 Share Posted October 8, 2009 Up... Link to comment Share on other sites More sharing options...
Guest Adriano Posted October 8, 2009 Share Posted October 8, 2009 in questo stesso forum sono consigliate le impostazioni del ffb di Gilles vedi nel thread dedicato al DFP Link to comment Share on other sites More sharing options...
Guest Chico Posted October 8, 2009 Share Posted October 8, 2009 Grazie adriano, quindi posso utilizzare i valori impiegati per il dfp? Pensavo esistesse qualcosa di specifico per il G25. Ti ringrazio. Link to comment Share on other sites More sharing options...
uru Posted October 8, 2009 Share Posted October 8, 2009 Grazie adriano, quindi posso utilizzare i valori impiegati per il dfp? Pensavo esistesse qualcosa di specifico per il G25. Ti ringrazio. Volevo chiederti se queste impostazioni potrebbero andare bene anche per GT Evo. Se si, saresti allora molto gentile a dirmi come ti sei trovato con le stesse sul G25 . Ieri ho ricevuto il G25 con la ARC Mod ed ho provato GT Evo ma vorrei ottimizzare le sensazioni. Solo che i parametri sono troppi ed io lo uso poco. Anzi, mi servirebbero anche per RFactor... Link to comment Share on other sites More sharing options...
Guest Chico Posted October 8, 2009 Share Posted October 8, 2009 Uru ti faro' sapere Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now