Fanatec Podium Series - base direct drive + novità SimRacing Expo 2019 - Page 78 - Volanti - Wheel - DrivingItalia.NET simulatori di guida Jump to content

Fanatec Podium Series - base direct drive + novità SimRacing Expo 2019


VELOCIPEDE

Recommended Posts

Alla peggio vado di Dremel e taglio le 5 viti che sono in dotazione alla Rseat, dopotutto e' un lavoretto da pochi minuti. 5 viti sono piu' che sufficienti e se ne hanno messe 2 in piu' della CSL/CSW e' proprio per una maggiore presa tanto se poi e' un limite strutturale della Rseat lo scopriamo presto dato che mancano solo 8 giorni alla spedizione della mia base DD2. 

Link to comment
Share on other sites

  • Replies 2.4k
  • Created
  • Last Reply

Top Posters In This Topic

  • Alfred ita

    465

  • Lele "NightRider" Albanes

    392

  • Fabio Viola

    290

  • VELOCIPEDE

    219

5 hours ago, Alfred ita said:

Alla peggio vado di Dremel e taglio le 5 viti che sono in dotazione alla Rseat, dopotutto e' un lavoretto da pochi minuti. 5 viti sono piu' che sufficienti e se ne hanno messe 2 in piu' della CSL/CSW e' proprio per una maggiore presa tanto se poi e' un limite strutturale della Rseat lo scopriamo presto dato che mancano solo 8 giorni alla spedizione della mia base DD2. 

Tu hai la DD2? Allora se regge la tua, la mia deve per forza di cose visto che ho preso il DD1 

Link to comment
Share on other sites

Il nostro amico Francesco @Tranky Fra Trancanelli ci mostra un veloce test in pista con Assetto Corsa del nuovo volante Fanatec Podium Direct Drive 😉

 

 

Link to comment
Share on other sites

Ciao a tutto il forum.

Come tutti voi sono in piena scimmia da Podium, il questi giorni mi sto scervellando tra misure e layout  dei fori della Wheel Base per capire se il DD1 andrà sulla mia GT Omega Pro

https://www.gtomegaracing.com/gt-omega-gaming-simulator-cockpits/gt-omega-pro-racing-simulator-professional-rs6-seat

sul sito GT Omega riporta questo:

"

The cockpit comes pre-drilled to hard-mount the:
• Logitech G25, G27, G29, G920 Wheel, pedals and shifter 
• Thrustmaster T500RS, T300RS, wheel and pedals, TH8RS/ TH8A shifter.
• Thrustmaster TX Racing Wheel and pedal. the Ferrari 458 Italia Edition for Xbox one
• Fanatec Porsche and CSR, Clubsport Wheel and the Clubsport pedals. Fanatec SQ Shifter.
• To Hard-mount the Fanatec CSR Shifters you will need to use the “Fanatec Shifter Brackets” 
• Thrustmaster Ferrari F430 Wheel and pedals
"
 
 
Credo che il DD1 ci andrebbe tranquillamente con le staffette laterali della CSW 2.5, così come ci va appunto la 2.5, anche perchè i "buchi" del DD1 e della 2.5 sono negli stessi punti proprio per fissare i supporti laterali.
 
...il problema è che nel "pacco" del DD1 le staffe non sono incluse.

Qualcuno di voi ha la Gt Omega e si è posto il mio stesso problema?
Edited by marpado
Link to comment
Share on other sites

8 hours ago, Fabio Viola said:

Che io sappia la V 2.5 non ha agganci laterali ma solo i fori posti sotto la base

Confermo..solo fori sotto con il classico pattern triangolare di Fanatec.

Inoltre Fanatec fornisce sempre(o lo si può scaricare dal sito) il foglio con disegnati i fori di fissaggio, credo che per il Podium sia lo stesso quindi fare gli altri due fori è facilissimo,basta un trapano. 

Considerando che tutte le postazioni hanno gia preforati i buchi per le viti basterà sovrapporre il cartoncino ai buchi gia esistenti e forare i due che mancano.

Link to comment
Share on other sites

On 4/22/2019 at 11:50 AM, Fabio Viola said:

Quindi i bulloni che usavo per il fissaggio della CSL Elite sono troppo lunghe per Podium?

sono da 20 mm mentre dal manuale si legge che devo usare delle M6 da 12 mm

Certo che però cosa gli cambiava metterli dentro la confezione?

si parla di 5+4 bulloni!

quanto gli avrebbe potuto incidere come prezzo?

 

 

Non tutte le postazioni hanno la piastra spessa uguale.

Quindi sarebbe comunque impossibile per loro mettere le viti lunghe giuste. 

Ad esempio sulla mia postazione SRC con il desk ricavato dal pieno ci vanno viti più lunghe.

I 12 MM che citano sono quello che sporge dalla piastra non la lunghezza totale della vite. 

Comunque qualsiasi ferramenta ha le viti di tutte le lunghezze possibili ed immaginabili.

 

Link to comment
Share on other sites

fattela passare la scimmia,i problemi semmai ci saranno li risolverai in maniera veloce ed intuitiva quando accanto alla postazione avrai il motore da montarci sopra. LOL

Link to comment
Share on other sites

Arrivata la mail del preorder del F1 2019:

Dear valued customer,
 

As promised, we’re giving you special access to the new, limited edition

ClubSport Steering Wheel F1® 2019,officially licensed by Formula1™! 


Simply log in to your Fanatec account, and you will see the new wheel listed in the Steering Wheels section of the Products menu.

You will have special access to this product page between April 24th and April 26th. After this, the page will be visible to all customers, after which we can’t guarantee that you will secure a unit. Last year, our F1® 2018 wheel sold out in a matter of hours (2018 units) and we are producing one more unit this year for a total of 2019 units, so grab it while you can!

Please note: The webshop voucher which we provided after the delay announcement (which can be used for any product) expires on December 7th 2019. If you have already used your voucher, you can still purchase this limited edition F1® 2019 wheel.

 

f1_04.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.