uru Posted January 18, 2019 Share Posted January 18, 2019 46 minutes ago, Cip060 said: Ma non si può rimettere il vecchio firmware se funzionava? Aspetto un po' per decidere se farlo. Perderei i profili salvati ma ci metto poco a riscriverli. Link to comment Share on other sites More sharing options...
Loris88 Posted February 10, 2019 Share Posted February 10, 2019 Chiedo scusa ma i link in prima pagina non funzionano. Grazie. Link to comment Share on other sites More sharing options...
ivaldi85 Posted February 23, 2019 Share Posted February 23, 2019 Scusate, sarà sicuramente scritto da qualche parte ma dove si può trovare la lista dei pezzi necessari per completare un DD? Grazie Link to comment Share on other sites More sharing options...
Eu Genio Posted April 1, 2019 Share Posted April 1, 2019 Ciao ragazzi, qualcuno di voi ha qualche schema sui collegamenti che si possono fare tra STM32 e il driver controller per motori stepper? In particolare io ho la stm32f407 e sul controller i collegamenti sono i seguenti a parte i pin del motore e corrente (L N) gli altri in alto dove vanno collegati? mi riferisco a questi in basso 1 PU+ Positive terminal of input photoelectric isolation signal Can be driven by +5 V-+24 V 2 PU- DP5 = OFF, PU is step-by-step impulse signal Falling edge is effective; whenever the impulse drops from high to low, the motor moves one step. Requirements: pulse width> 2.5μS DP5 = ON, PU is positive step-by-step impulse signal 3 DR+ Positive terminal of input photoelectric isolation signal Can be driven by +5 V-+24 V 4 DR- DP5 = OFF, DR is direction control signal Used to change turning direction of the motor. Requirements: pulse width> 2.5μS DP5 = ON, DR is negative step-by-step impulse signal 5 MF+ Positive terminal of input photoelectric isolation signal Can be driven by +5 V-+24 V 6 MF- The motor release signal When it is active (at low level), the motor wiring current is turned off, and the driver stops working; the motor is in a free mode. 7 RDY+ The driver is ready to output positive photoelectric isolation signal. When the driver is in normal state, ready to receive controller signal, the signal is active (at low level). 8 RDY- The driver is ready to output negative photoelectric isolation signal. Link to comment Share on other sites More sharing options...
Eu Genio Posted April 2, 2019 Share Posted April 2, 2019 (edited) ok ragazzi ho trovato da solo le risposte... linko il pdf magari servirà a qualcuno un domani:https://www.xsimulator.net/community/attachments/quick-tutorial-pdf.40607/ Ciao a tutti e buon esperimenti (tra qualche mesetto pubblicherò il mio ) Edited April 2, 2019 by Eu Genio Link to comment Share on other sites More sharing options...
Lele "NightRider" Albanes Posted April 3, 2019 Share Posted April 3, 2019 10 hours ago, Eu Genio said: ok ragazzi ho trovato da solo le risposte... linko il pdf magari servirà a qualcuno un domani:https://www.xsimulator.net/community/attachments/quick-tutorial-pdf.40607/ Ciao a tutti e buon esperimenti (tra qualche mesetto pubblicherò il mio ) Credo che troverai più aiuto qui: Questo thread ormai è dedicato alla versione commerciale degli OSW che da tempo ha smesso di essere un progetto amatoriale. Link to comment Share on other sites More sharing options...
Lele "NightRider" Albanes Posted April 3, 2019 Share Posted April 3, 2019 Ragazzi che ne pensate? https://www.simucu.be/sc2sport-direct-drive-wheel-base Link to comment Share on other sites More sharing options...
Filodream Posted April 3, 2019 Share Posted April 3, 2019 Detto fatto proprio. Anzi, ancora prima che il Podium ce l'avessimo in mano. Ho letto tutto ed è molto interessante. Se a qualcuno interessa il preorder di un dd1 mi faccia sapere in privato. Link to comment Share on other sites More sharing options...
Cip060 Posted April 3, 2019 Share Posted April 3, 2019 Soloi 1300 euro un AFFARE Link to comment Share on other sites More sharing options...
PICIA.71 Posted April 3, 2019 Share Posted April 3, 2019 57 minutes ago, Filodream said: Detto fatto proprio. Anzi, ancora prima che il Podium ce l'avessimo in mano. Ho letto tutto ed è molto interessante. Se a qualcuno interessa il preorder di un dd1 mi faccia sapere in privato. Anche io interessato al Fanatec ma oggi ho visto questi e il pro mi stuzzica . Visto che sei un Guru per me mi potresti consigliare dove meglio acquistare questi DD? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now